Enable the AirPlay 2 build to operate an optional classic-AirPlay-only service or to gracefully degrade to classic AirPlay, as follows:
1. Add a new command-line option '-—service-type=<type>' and an equivalent configuration entry 'service_type = "<type>"' in the 'general' section of the configuration file,
where <type> can be "auto", "classic" or "airplay2":
1. "auto" (default) means that the service will be AirPlay 2 if NQPTP is running. If NQPTP is not running, classic AirPlay service will be provided instead, and in that case,
"(Classic)" will be appended to the default AirPlay service name visible to AirPlay clients like Apple Music, for example "RaspberryPi3B (Classic)".
2. "classic" means the service will be classic AirPlay (aka AirPlay 1).
3. "airplay2" means the service will be the modern AirPlay 2. In this case, as distinct from "auto", if NQPTP is not running, Shairport Sync will log an error and terminate.
2. In the systemd service file, NQPTP is now a "Want" rather than a "Require". If it's present, then it will be launched before Shairport Sync. If it's absent, Shairport Sync will launch anyway.
3. Improve the delivery of input format changes and emit 'sdsc' metadata when changes occur.
4. Emit new format information in the log if statistics is enabled.
Docker Changes
1. Support for linux/arm/v6 has been dropped, as Docker is no longer supported.
2. NQPTP is not started in the AirPlay 2 Docker image if '--service-type=classic' or '--service-type=airplay1' is in the command line options at the end of the docker run command.
The purpose is to ensure that ports 319 and 320 are left alone when the AirPlay 2 image is set to provide Classic service only.
Note that setting the configuration file 'service_type' to 'classic' will not prevent NQPTP from starting up -- you must use the command line option.
3. A new "dev" target has been added. It is a large image containing the custom-built FFmpeg library, NQPTP, Avahi and D-Bus along with the Shairport Sync source and
all necessary development tools. When started, Avahi, D-Bus and NQPTP are all installed and running. The bash shell has also been added and is entered.
Stability Improvements
Reorganise session preemption to fully terminate the existing session before starting a new one.
Don't delay closing the event port to wait for it to be closed at the client end.
Add a safe_socket_close() function to ensure sockets are fully closed. Use -1 to designate closed rather than 0, to prevent attempts to reclose sockets, causing mayhem.
Re-order FFmpeg decommissioning during teardown.
- 48,000 frames per second operation,
- 48k lossless stereo, 5.1 and 7.1 surround sound
- Multichannel and multi rate operation on ALSA, PipeWire, PulseAudio, FreeBSD, stdout and unix pipe output backends.
Automatic, flexible and controllable output format (rate, sample format and channel count) selection.
Full FFmpeg integration to support transcoding, resampling, and new audio formats.
Better operation on lower powered devices down to e.g. Raspberry Pi B.
Reduced Docker image sizes with a slimmed-down FFmpeg library.
Enhanced timestamp handling for better synchronization.
Improved the sync error calculation.
A new "vernier" resampling and interpolation method for low-power CPUs.
Bug fixes and minor enhancements.
Note -- there are many breaking changes from previous versions of Shairport Sync!
nqptp.c listens on "localhost", but shairport-sync connectes to the wildcard
address 0/0. This apparently works on Linux and FreeBSD, but OpenBSD fails:
```
$ ktrace shairport-sync -v -u
[...]
0.000038288 "ptp-utilities.c:243" *fatal error: error sending timing_peer_list to NQPTP
0.000021868 "shairport.c:1728" emergency exit
$ kdump
[...]
2319 shairport-sync STRU struct sockaddr { AF_INET, 0.0.0.0:9000 }
2319 shairport-sync RET sendto -1 errno 51 Network is unreachable
[...]
```
Resolve and connect to "localhost" just like NQPTP does, resulting in
127.0.0.1 or ::1 as socket addresses.
This is required to run when configured `--with-airplay-2`.
Tested on OpenBSD/amd64 7.4-current with shairport-sync 2.4.3 and nqptp
1.2.5-dev cfa8315 (plus OpenBSD fixes).
I expect Linux and FreeBSD to work as before, but have not tested it.
Add three parameters to the backend play() function call -- (1) a flag indicating whether the samples are timed or not. If timed, (2) the timestamp and (3) the local time at which the first frame should be heard.
Update missing pipewire library message.
Makefile.am fix.
Update the SHM version and fix the SHM name so that it works with FreeBSD.
Remove redundant (?) AC_HEADER_STDC check.
Fix compilation and installation under FreeBSD -- changes to allow building in a separate directory broke the FreeBSD build process.
Add AC_CHECK_LIB for gcrypt in case PKG_CHECK_MODULES fails to find it.
Find gcrypt using pkg-config
Add code to detect when the RTSP channel goes idle for a period, and use it to reset clocks and timings, etc. so that SPS resumes correctly where the source has gone to sleep while playing a realtime stream and has subsequently woken up.
Don't exit if a UDP Clock Control packet is empty. Also check minimum packet size.
Remove some very experimental code which may cause memory and port leaks.
Strip file path from the filename used in debug messages, information messages, warnings and fatal error messages.
BB fix to Makefile.am -- overwriting the DBUS stuff with MPRIS definitions, duh.
Fix some problems building on FreeBSD and tidy up the use of the "sed" editor.
Fix some problems building on picore.
Fix an uninitialised variable
start using the "nqptp" SMI
Mike Brady
Klemens NanniandKlemens Nanni