diff --git a/scripts/shairport-sync.conf~ b/scripts/shairport-sync.conf~
deleted file mode 100644
index 797e8e4f..00000000
--- a/scripts/shairport-sync.conf~
+++ /dev/null
@@ -1,75 +0,0 @@
-// Sample Configuration File for Shairport Sync
-// Commented out settings are generally the defaults, except where noted.
-
-// General Settings
-general =
-{
-//	name = "Shairport Sync Player"; // This is the name the service will advertise to iTunes. The default is "Shairport Sync on <hostname>"
-//	mdns_backend = "avahi"; // not used, not tested
-//	output_backend = "alsa"; // alsa is default, other possibilities are "stdout", "pulse", "dummy". Only alsa supports synchronisation.
-//	port = 5000;
-//	password = "secret"; // default is no password
-//	interpolation = "basic"; // aka "stuffing". Default is "basic", alternative is "soxr"
-//	statistics = "no"; // print statistics in the log
-//	drift = 88; // allow this number of frames of drift before correcting it
-//	resync_threshold = 2205; // a synchronisation error greater than this will cause resynchronisation; 0 disables it
-//	log_verbosity = 0; // "0" means no verbosity, "3" is most verbose.
-//  ignore_volume_control = "no"; // set this to "yes" if you want the volume to be at 100% no matter what the source's volume control is set to.
-};
-
-// Latencies for different sources.
-latencies =
-{
-//	default = 88200;
-//	itunes = 99400;
-//	airplay = 88200;
-//	forkedDaapd = 99400;
-};
-
-
-// How to deal with metadata, including artwork
-metadata =
-{
-//	enabled = "no";
-//	include_cover_art = "no";
-//	pipe_name = "/tmp/shairport-sync-metadata";
-};
-
-// Advanced parameters for controlling how a Shairport Sync runs
-sessioncontrol = 
-{
-//	run_this_before_play_begins = "/path/to/application and args";
-//	run_this_after_play_ends = "/path/to/application and args";
-//	wait_for_completion = "no";
-//	allow_session_interruption = "no";
-//	session_timeout = 120;
-};
-
-//
-// Back End Settings
-//
-
-// These are parameters for the alsa back end, the only back end that supports synchronisation
-{
-//  output_device = "default";
-//  mixer_type = "software"; // "software" or "hardware"
-//  mixer_device = "default"; //actually, the mixer default is whatever the output_device is. Normally you wouldn't have to use this.
-//  mixer_control_name = "PCM"; // the name of the mixer to use -- there is no default.
-//  audio_backend_latency_offset = 0; // Set this offset to compensate for a fixed delay in the audio back end. E.g. if the output device delays by 100 ms, set this to -4410.
-//  audio_backend_buffer_desired_length = 6615; // If set too small, buffer underflow occurs on low-powered machines. Too long and the response times with software mixer become annoying.
-};
-
-// These are parameters for the pipe back end, an experimental back end that directs output to a pipe.
-pipe =
-{
-//  audio_backend_latency_offset = 0; // Set this offset to compensate for a fixed delay in the audio back end. E.g. if the output device delays by 100 ms, set this to -4410.
-//  audio_backend_buffer_desired_length = 44100;
-//  name = "/path/to/pipe"; // there is no default pipe name for the output
-};
-
-// These are parameters for the stdout back end, an experimental back end that directs output to stdout.
-stdout =
-{
-//  audio_backend_latency_offset = 0; // Set this offset to compensate for a fixed delay in the audio back end. E.g. if the output device delays by 100 ms, set this to -4410.
-//  audio_backend_buffer_desired_length = 44100;
-};