ebusd/docs/enhanced_proto.md

Transfer speed

In order to compensate potential overhead of transfer encoding, the transfer speed is set to 9600 Baud with 8 bits, no parity, and 1 stop bit.

Protocol

Data bytes with a value below 0x80 can be transferred as is.

Data bytes with value above or equal to 0x80 are split up into two bytes, each one with the highest bit set to 1. The second bit indicates whether it is the first or second byte of a split transfer. This way protocol errors can easily be detected. The bits in the two bytes look like this:

first    second
76543210 76543210
11ccccdd 10dddddd

4 bits in c are used for indicating a special purpose and is set to one of the command request/response symbols as stated below.
8 bits in d are the data byte to be transferred (might also be unused).

Command request/response symbols

from ebusd to interface

• initialization request
  <INIT> <features>
  Requests an initialization of the interface and requests special features in the data byte (tbd).
• send data request
  <SEND> <data>
  Requests the specified data byte in d to be sent to the eBUS.
  For data byte values <0x80, the short form without the <SEND> prefix is allowed as well.
• arbitration start request
  <START> <master>
  Requests the start of the arbitration process after the next received <SYN> symbol with the specified master address in d.

from interface to ebusd

• initialization response
  <RESETTED> <features>
  Indicates a reboot or an initial ebusd connection on the interface and is expected to be returned after an <INIT> request.
  The data byte d indicates availability of certain features (like full message sending instead of arbitration only, tbd).
• receive data notification
  <RECEIVED> <data>
  Indicates that the specified data byte in d was received from the eBUS.
  For data byte values <0x80, the short form without the <RECEIVED> prefix is allowed as well.
• arbitration start succeeded <STARTED> <master>
  Indicates the the last arbitration request succeeded (arbitration was won).
  The data byte in d contains the master address that was sent to eBUS during arbitration.
• arbitration start failed
  <FAILED> <master>
  Indicates that the last arbitration request failed (arbitration was lost or sending failed).
  The data byte in d contains the master address that was sent to eBUS during arbitration.

Symbols

These are the predefined symbols as used above.

Bus symbols

• SYN 0xAA

Command request symbols (from ebusd to interface)

• INIT 0x0
• SEND 0x1
• START 0x2

Command response symbols (from interface to ebusd)

• RESETTED 0x0
• RECEIVED 0x1
• STARTED 0x2
• FAILED 0xa

Examples

Passive receive

The master-slave data sequence (without SYN, ACK, and CRC) 1008951200 / 0164 when ebusd is only listening to traffic on the bus would usually be transferred as follows (with all extra symbols seen on the bus):

order	eBUS proto	eBUS byte	sender	enhanced proto	enhanced bytes
1	SYN	0xAA	interface	<RECEIVED> <0xAA>	0xC6 0xAA
2	QQ	0x10	interface	<0x10>	0x10
3	ZZ	0x08	interface	<0x08>	0x08
4	PB	0x95	interface	<RECEIVED> <0x95>	0xC6 0x95
5	SB	0x12	interface	<0x12>	0x12
6	NN	0x00	interface	<0x00>	0x00
7	CRC	0xB1	interface	<RECEIVED> <0xB1>	0xC6 0xB1
8	ACK	0x00	interface	<0x00>	0x00
9	NN	0x01	interface	<0x01>	0x01
10	DD	0x64	interface	<0x64>	0x64
11	CRC	0xFF	interface	<RECEIVED> <0xFF>	0xC7 0xBF
12	ACK	0x00	interface	<0x00>	0x00
13	SYN	0xAA	interface	<RECEIVED> <0xAA>	0xC6 0xAA

Active successful send

The same data sequence 1008951200 / 0164 when initiated by ebusd as master (with address 0x10) would usually be transferred as follows (with all extra symbols seen on the bus):

order	eBUS proto	eBUS byte	sender	enhanced proto	enhanced bytes
1			ebusd	<START> <0x10>	0xC8 0x90
2	SYN	0xAA	interface	<RECEIVED> <0xAA>	0xC6 0xAA
3			interface	<STARTED> <0x10>	0xC8 0x90
4	QQ	0x10	interface	<0x10>	0x10
5	ZZ	0x08	ebusd	<0x08>	0x08
6	ZZ	0x08	interface	<0x08>	0x08
7	PB	0x95	ebusd	<SEND> <0x95>	0xC6 0x95
8	PB	0x95	interface	<RECEIVED> <0x95>	0xC6 0x95
9	SB	0x12	ebusd	<0x12>	0x12
10	SB	0x12	interface	<0x12>	0x12
11	NN	0x00	ebusd	<0x00>	0x00
12	NN	0x00	interface	<0x00>	0x00
13	CRC	0xB1	ebusd	<SEND> <0xB1>	0xC6 0xB1
14	CRC	0xB1	interface	<RECEIVED> <0xB1>	0xC6 0xB1
15	ACK	0x00	interface	<0x00>	0x00
16	NN	0x01	interface	<0x01>	0x01
17	DD	0x64	interface	<0x64>	0x64
18	CRC	0xFF	interface	<RECEIVED> <0xFF>	0xC7 0xBF
19	ACK	0x00	ebusd	<0x00>	0x00
20	ACK	0x00	interface	<0x00>	0x00
21	SYN	0xAA	interface	<RECEIVED> <0xAA>	0xC6 0xAA

Active successful send as SYN generator

The same data sequence 1008951200 / 0164 when initiated by ebusd as master (with address 0x10) and acting as SYN generator would usually be transferred as follows (with all extra symbols seen on the bus):

order	eBUS proto	eBUS byte	sender	enhanced proto	enhanced bytes
1			ebusd	<START> <0x10>	0xC8 0x90
2	SYN	0xAA	ebusd	<SEND> <0xAA>	0xC6 0xAA
3	SYN	0xAA	interface	<RECEIVED> <0xAA>	0xC6 0xAA
4			interface	<STARTED> <0x10>	0xC8 0x90
5	QQ	0x10	interface	<0x10>	0x10
...	see above
The rest of the communcation is the same as before (from 5.)

Active failed traffic

A failed arbitration when initiated by ebusd as master (with address 0x15) would usually be transferred as follows (with all extra symbols seen on the bus):

order	eBUS proto	eBUS byte	sender	enhanced proto	enhanced byte
1			ebusd	<START> <0x10>	0xC8 0x90
2	SYN	0xAA	interface	<RECEIVED> <0xAA>	0xC6 0xAA
3		0x10	ebusd	<FAILED> <0x10>	0xE0 0x90
4	QQ	0x03	interface	<0x03>	0x03